![]() On the ground one-half mile is the same as 4.4 inches on the map. Measured distance = 2,640 feet 1 inch = 4.4 inches Step 2. Use the map scale from Example 6 to find the map distance. Measured distance = known distance / map scale Step 1. Set up the cancellation table so all units will cancel, except the desired unit, feet. Rearrange terms by multiplying each side by the measured distance and dividing each side by the map Map scale = known distance / measured distance How many inches is does this distance correspond to on the map? The known ground distance between points B and C is 1/2 mile. What is the scale in units of inches/foot?Įxample 5 - Use the map scale in example 6. Also, if a map has section lines, the distance between section lines is typically 1 mile.Įxample 4 - The distance between point A and B is 6 inches on the map. The scale can be calculated by knowing the distance between two points on the map, and measuring the distance on the map. Occasionally, a map may not provide a scale. Step 3. Set up the cancellation table so all units will cancel, except the desired unit, inches.ġ2,000 feet = 182 chains = 2.3 miles = 144,000 inches Step 2. Set up the cancellation table so all units will cancel, except the desired unit, miles. Step 1. Set up the cancellation table so all units will cancel, except the desired unit, chains. Example 3b - Using the information in Example 3a, find the ground distance in chains, miles, and inches.Multiply the total number of dots by the conversion factor on the map scale to determine the total acreage. Count every other dot when dots fall on the boundary line. ![]() Place the acreage grid transparency over the area to be measured.Ĭount dots inside the sketched area. Table 5.2 Acreage Grid Overlay, Map Scales, and Equivalents. To use the acreage grid transparency, follow these steps: USING THE MODIFIED ACREAGE GRID (TRANSPARENCY) Set up the cancellation table so all units will cancel, except the desired unit, feet. Step 1. Set up the cancellation table so all units will cancel, except the desired unit, miles/inch.Įxample 3a - The map distance between two points is 6 inches. On the map 1 inch is equal to 2,000 feet on the ground, 1:2,000 (in/ft).Įxample 2 - Convert the 1:2,000 (in/ft) to (in/mile). Step 1. Set up the cancellation table so all units will cancel, except the desired unit, ft/in. Ground distances on maps are usually given in feet or miles.Įxample 1 - Convert the map scale of 1:24,000 (in/in) to (in/ft). For example, a map scale indicating a ratio of 1:24,000 (in/in), means that for every 1 inch on the map, 24,000 inches have been covered on the ground. It is given as a ratio of inches on the map corresponding to inches, feet, or miles on the ground. Increase the percentage to increase the width of the timescale.The map scale is printed in the map legend. In the Size box, reduce the percentage to reduce the width of the timescale.Click the Close button on the toolbar in print preview.If you do not get the result you want, continue to the next step. To work around this behavior in Project 2007 and earlier versions, use any of the following methods. Whereas signed and unsigned integer data types have a default binary point to the. When you scale your project for printing, the project information is scaled proportionally for height and width. Fractional numbers are distinguished from integers by their default scaling. Choose the scaling option you want to use.If you want to scale the entire project (not just the timescale portion as in method 1), scale the entire project to fit the number of pages you want. Click to select the Fit Timescale to End of Page check box.To turn on the Fit Timescale to End of Page option, follow these steps: This prevents a page from being printed with bars or data on only a small fraction of the pages, which would result in an additional blank timescale beyond the last bar or column of data. The Fit Timescale to End of Page option enlarges or reduces the width of the timescale to match the end of a page. In the Size box, reduce the percentage to reduce the width of the timescale, Increase the percentage to increase the width of the timescale.On the Timescale drop-down list, click Timescale. Click to clear the Fit timescale to end of page check box.On the File tab, click Print, and then click Page Setup.If the Fit Timescale to End of Page option is selected, turn off this option, and manually change the timescale. To work around this behavior in Project 2010 & 2013, use any of the following methods. In Microsoft Project, when you print or print preview a Gantt Chart view or a Usage view, task bars or columns of data may be printed on more pages than necessary, or you may see an additional timescale beyond the end of your project.
0 Comments
Leave a Reply. |